#Nvidia only shows 3d settings install#
#Nvidia only shows 3d settings plus#
#Nvidia only shows 3d settings windows#

After I switched on the power for a few seconds, it says I have critically low battery. A few days ago while I was using my laptop, i forgot to switch on the power adaptor and the battery was drained to critical, and the laptop wasnвЂ™t able to turn on. I was able to open the NVIDIA setting through my second monitor just fine. I am using a second monitor for my laptop so itвЂ™s always in a closed position while IвЂ™m using it. IвЂ™ve been using your plugable UD-3900 product for 7 months now without a problem. Image not as good as 2d 4k but I think iвЂ™ve reached the limits of the G2 as far as clarity is concerned.Hi guys, I need some help. Also increasing render scaling >100 degraded clarity somewhat. tried raising ansio and tss but seemed to degrade image. raised most settings to Ultra and sliders to 200. Cleaned it up nicely and getting smooth and clear. At first not a discernable change so I reset FS settings to default. WIP.Д®dit + 2hours - CPL set to default then relvant functions to Application to Decide. Continuing to experiment and will give these suggestions above a go.

But still need to tweak and fine tune, presuming of course that there are no bugs. So far its looking pretty good that a lot of negatives have been addressed. However at 150 seemed to be quite smooth over London. At this level no CTD but frames must be less than 10/sec.

#Nvidia only shows 3d settings plus#

On the plus side, have ramped up render scaling in FS to 200. Cockpit images clean and readable but could be a bit crisper for my liking.

As discussed above, changing Aniso does not seem to have any effect on image and menu boxes have slightly jagged edges.

#Nvidia only shows 3d settings windows#

Looking out of side windows its jittery: maybe 2 or 3 frames. Smooth flying and clear detail looking forward through windscreen. Nvidia CPL settings as per CptLucky8 of April (I think).

#Nvidia only shows 3d settings install#

PS: IвЂ™m not done yet adjusting for the Index, thus IвЂ™ve not tried the G2 with SU5 HF2 yet.Д¬lean install of MSFS and updated Windows and OXR. This is one area IвЂ™d really like to figuring out, at least just by mere curiosity for these sort of things! What I mean by this is that it is has if both FS2020 and Optical Flow are fighting for the card silicon, which could be the case if for example FS2020 would be using compute shaders for example and if those would take a longer processing time when on the ground (handling much more things). IвЂ™ve been wondering whether FS2020 wouldnвЂ™t be using the GPU in a way which is interfering with the Turing silicon the NVidia Optical Flow lib is using for motion smoothing. PS: about вЂњFS2020 on ground taking too many resources while on ground to the point I have to disable motion smoothingвЂќ: this one is puzzling me still because in 2D I can see there is still enough room on the CPU/GPU. This is a short feedback post to share the experience!

It has been months though that IвЂ™m only using motion smoothing at 18fps so I go used to the artefacts instead! Switching back to motion smoothing off was slightly uncomfortable at first because of the juddering but at 45fps it was not so bad after a short while, especially if you develop the habit of rotating the head (reprojection kicking it) instead of translating it (juddering is unavoidable in this case). If you read this topic from the beginning and when VR was initially available, I was explaining how 30fps constant is still useable in practice with the A320 (not FBW back then) and after a while you get used to the juddering. IвЂ™ve been able to keep 30fps (SS 152% and all the rest unchanged) on the ground, and when up in the air 45fps, and this was not bad at all to me. Yesterday IвЂ™ve tried the FBW A320 latest dev version but this time with motion smoothing off. What stroke me is how much FS2020 has a struggle when on ground, to the point I have to disable motion smoothing otherwise FS2020 is like rendering pairs of frames in reverse order (displaying frame 2 first, then frame 1 next, then frame 4, then frame 3 etcвЂ¦ this is what it looks like). With the 9700K+2070S I can barely push beyond 152% and 18fps with the Index and FS2020 with aircraft with lots of EFIS for example, like the FBW A320 (for this one I must go 15fps on ground but can switch back to 18fps in the air) (NB: I can push much higher with XP11 though) Motion smoothing is taking more resources and usually you can balance this out with fewer frames per sec (and artifacts of course). IвЂ™ve done a few more tests yesterday about this. My 2070 SUPER VR settings and suggestions (Index - SteamVR)